Loading...
This site is best viewed in a modern browser with JavaScript enabled.
Something went wrong while trying to load the full version of this site. Try hard-refreshing this page to fix the error.
Kualifikasi Teknisi DAYMARC Handler
bundet
Board mana yang salah pada pesan "BOARD 1 ERROR" (Which board is faulty on a "BOARD 1 ERROR" message)? -> Shuttle Board
Papan yang mengontrol pergerakan vertikal dan horizontal distributor (Board that controls the vertical and horizontal movement of the distributor). -> Bin control board
Bagian pada pawang yang memegang tabung bagian dan menunggu untuk diuji (Part on the handler that holds tubes of parts and waiting to be tested). -> Infeed stacker
Membawa tabung dari gripper dan siklus bagian ke track singator infeed (Takes tubes from gripper and cycles parts to the infeed singulator track). -> Robot arm
Board digunakan untuk mengontrol pergerakan robot, stripper & gripper motor (Board used to control the movement of robot, stripper & gripper stepper motor). -> Feeder board
Papan yang memberikan sinyal handshaking ke tester (Board that gives handshaking signal to the tester). -> Interface board
Bongkar komponen yang diuji dari lintasan uji dan urutkan ke jalur tempat tidur pembongkaran yang tepat (Unloads the tested parts from the test track and sort them to the proper unload bed track). -> Distributor
Bagian dari panel kontrol utama yang mengatur suhu tes yang diinginkan dalam derajat celcius positif atau negatif (Part of the main control panel that sets the desired test temperature in the positive or negative degrees centigrade). -> Set point thumbwheel
Ketika ditekan, switch ini melepaskan kekuatan ke Robot, Gripper, dan motor Stripper (When pressed, this switch disengages power to the Robot, Gripper, and Stripper motors). -> Loader access
Layar fluoresensi hampa dua puluh karakter yang menunjukkan status sistem dan informasi pemeliharaan (A twenty character vacuum fluorescent display that indicates system status and maintenance information). -> Alphanumeric display
Bertanggung jawab untuk penggantian tabung keluaran yang diisi secara otomatis dengan yang kosong pada lintasan output 7 dan 8 (Responsible for automatic replacement of filled output tubes with empty ones at output tracks 7 and 8). -> Auto tube
Dalam penangan tri-temp Daymarc, selama operasi pawang melakukan hal berikut kecuali untuk (In Daymarc tri-temp handler, during operation the handler performs the following except for). -> Device are tested after soaking on the unload bed (Perangkat diuji setelah direndam di tempat tidur lepas).
Bagian dari tumpukan infeed yang melepaskan perangkat satu per satu ke ruang (Part of the infeed stack that release the device one at a time to chamber). -> Infeed singulator
Kesalahan board # 4 sesuai dengan (Board error # 4 corresponds to). -> Error on Temp. control board
Nomor tes mandiri apa yang digunakan untuk mengaktifkan situs uji solenoid dan bellow baik ON atau OFF state (What self test number is used to activate test site solenoids and bellows either ON or OFF state)? -> Self test # 2, test site valves
Persyaratan CDA dari Daymarc handler selama suhu rendah. operasi (CDA requirement of Daymarc handler during low temp. operation). -> 55 - 60 psi
TRACK ENTRY BLOCKAGE menunjukkan bahwa suatu perangkat adalah (TRACK ENTRY BLOCKAGE indicates that a device is). -> Blocking the track entrance sensor of the unload bed
Reflektif photosensor dipasang di bawah permukaan pemuatan tabung yang mendeteksi keberadaan tabung perangkat di lengan stripper (Reflective photosensor mounted under the tube loading surface which detects the presence of a tube of device in the stripper arm). -> Tube sensor
Pada menu Self Test 6, apa arti XX0XXXXX (On Self Test 6 menu, what does XX0XXXXX mean)? -> Distributor exit sensor 3 is unblocked (Sensor keluar Distributor 3 tidak diblokir).
Sensor suhu TS1 dapat ditemukan pada (Temperature sensor TS1 can be found on) -> Test site near actuator (Situs uji dekat aktuator).
Ketika terjadi macet di handler, kita dapat melihat lokasi macet di... (When a jam occurs in the handler, we can see the locate of jam at...) -> Sequence Indicator Display.